Some wrong maintenance methods

Some wrong maintenance methods

1, blindly remove the engine thermostat

If the blinder is removed due to high engine temperature, cooling

The liquid can only perform large circulation, can not adjust the cooling intensity, it is difficult to ensure that the engine works at a more suitable temperature, but the engine is often working at a low temperature, resulting in a decrease in engine power, accelerated wear, increased fuel consumption. If the engine thermostat occurs After troubleshooting or replacement, if the engine temperature is still high, other parts of the cooling system should be inspected and the thermostat can not be removed.

2, the engine temperature is not afraid of high fear of low

Some people think that the engine temperature is not afraid of high when driving, not afraid of low. In fact, when the engine temperature is low, the harm is also very great. Should be based on the normal temperature of the car instructions to drive in order to ensure the life of the engine.

3, engine idling temperature

When using idling heating, due to the low speed, the oil pump can not quickly press the lubricating oil into the various lubrication surfaces, the oil pressure is also low, so that the engine parts in the engine work under dry friction or semi-dry friction; fuel due to low temperature Poor atomization causes unburned fuel (air-fuel mixture) to enter the crankcase and flush away the oil film on the cylinder wall, which also accelerates the wear of the engine parts. Therefore, after the engine is started for a few seconds, the application of the engine is accelerated at a fast speed (in a modern car). Specially equipped with fast idle device, after the engine temperature rises, it will automatically adjust to idle state) to improve the lubrication conditions of the engine.

4, the tighter the water pump fan belt

The tighter the belt is not the better. The belt is too tight will not only make it stretch or break, shorten the service life of the belt, but also due to too much tension, leading to distortion of the generator shaft, the water pump shaft and early damage to the bearing. The tightness of the fan belt should meet the technical requirements. Normally, the deflection of the normal belt is 10-15mm.

5, use the torch to bake the oil

The use of a blowtorch to bake the oil in the winter will not only chemically change the additives in the oil and lose the original performance, but it will also cause the oil to gel and deform the oil base, which will easily cause fire. The best practice is to base on the local winter minimum The temperature is selected with the appropriate engine oil. It is best to park the vehicle in a garage with insulation facilities where conditions permit.

The more advanced methods of removal are ultrasonic cleaning and nuclear cleaning. However, the most common and simplest methods are physical removal and chemical removal. These two methods can also be used together.

Ss Spunbond Nonwoven Production Line

Non-woven fabric is a kind of non-woven fabric, which directly uses polymer chips, short fibers or filaments to form fibers through airflow or mechanical netting, and then undergo hydroentangling, needle punching, or hot rolling reinforcement, and finally finishing The resulting non-woven fabric. A new type of fiber product with soft, breathable and flat structure. The advantage is that it does not produce fiber debris, is strong, durable, silky soft, and has a cotton feel. Compared with cotton fabrics, non-woven bags are easy to shape, and It is cheap, durable, and disposable. Insulating and conductive. Softness and stiffness. Density and expansion. Isotropic, anisotropic. Filterability, breathable and impermeable. Elasticity and stiffness. Light, loose and warm. Thin as a cicada's wings, thick as felt. Waterproof and breathable. Ironing, stitching, and compression molding. Flame retardant and antistatic. Water-permeable, waterproof, abrasion-resistant, and flocking. Wrinkle resistant, good elasticity, high moisture absorption, water repellency. SS non-woven fabrics are mostly used in sanitary materials, so in the mechanical design, the SS machine tends to make the non-woven fabric softer, and the ss can also be processed to become more rigid and suitable for packaging materials.



Ss Spunbond Nonwoven Production Line,Ss Pp Spunbond Non-Woven Fabric Machine,Automatic Non-Woven Production Line,SS Spunbond Compounding Non Woven Production Line,SS Spunbond Nonwoven Machine

Changzhou Puyisen Machinery Technology Co., Ltd. , https://www.czsmmsmachine.com