Electrical Hose Crimping Tool for 1.5 Inch Hose

Electrical Hose Crimping Tool for 1.5 Inch Hose

Model NO.: KM-91Z
Crimping Range: 1/8"-1 1/4" 4sp
Machine Max Opening: 104mm
Die Material: Special Steel
Opening Time: Within 4s
Closing Time: Within 10.5s
Weight: 160kg
Volume (L-W-H): 640*480*660(mm)
Trademark: Kangmai
Transport Package: Standard Export Plywood Case
Specification: Approved CE and ISO
Origin: Handan, China
HS Code: 8462919000
Technical Datas Of Uptodate Hydraulic Hose Crimping Machine KM-91Z
Crimp ranger: 1/8"-1 1/4" 4SP
Standard voltage&motor:  380V/50HZ/3PH
Optional voltage&motor 220v,440v
Pump piston pump
Opening without dies φ104mm
Opening ≥20mm
No.of standard die 8 sets
Oil box 40L
Force 400T
System pressure 30Mpa
Weight without oil 160 kg
Machine size 640mm*480mm*660mm

Standard Die Size Of Hose Crimping Machine KM-91Z
Die bore 15mm 18mm 20mm 23mm 26mm 29mm 37mm 46mm
 length 65mm 65mm 65mm 65mm 65mm 65mm 65mm 78mm
Hose I D 6mm 8mm 10mm 13mm 16mm 19mm 25mm 32mm

Advantages Of Hyraulic Hose Crimping Machine KM-91Z:
NEW foam inserts introduced to protect your machine from debris dropping into
 the bottom of the head. With there you will minimize the risk of debris getting 
into the cylinder which could cause damage to seals and Other moving parts of 
the head. This will significantly extend the life of hydraulic hose crimping machine.

Applications Of Hydrauli Hose Crimping Machine KM-91Z
 1).Suitable for high precision pressing of low and high pressure hose diameter, starting from 1/8 inch to 1 1/4 inch internal hose pipe.
 2).Used rubber hose to transmit hydraulic pressure as there  working power.
 3).Used in Building Construction, Petroleum Industry, Chemical Industry, Car and motor Industry.

Hydrauli Hose Crimping Machine Why Not Choose Kangmai?
1). Kangmai hose crimper has approved CE & ISO and audited by SGS.
2). The fitting and hoses crimped by kangmai machine never leakage the oil and never broken. The reason are like below:
  (a)The machine head process by CNC machine, roundness and taper is within 0.1mm.
  (b)The machine die base and dies adopt special die steel and process by advances craft,the hardness is above 55HRC. The die hardness is enough so that the die life is very long and easy to crimp high pressure hydraulic hose, such as 4SP even 6SP.
  (c)The technical of machine head is forging not cast. Casting is cheap but has small hole on the machine head. The piston will divide from casting machine head.
3). Strictly testing and inspetion. 
 (a) for  raw material, we will check again by our inspector as per international standard. Only the raw material reach to international standard and allow enter kangmai facotry. 
 (b) for hydraulic and eletrical parts, such as valve, pump, motor and so on, we use famous brand both from China and abroad.However, we will check again when these parts enter our facotry. 
 (c) before the hose crimping machine enter our warehouse, the inspector check the machine roundess, taper, opening, speed, noise, apprance and so on. Only each parts is up to standard of ISO, CE standard, the machine can enter the warehouse. 
 (d) when the machine package, the inspector the dies, the package and other parts of clients requriment. Everything is ok, the inspector signed and machine allow to go out the facotry. 
 

Gravity Casting / Permanent mould casting

Aluminum Gravity Casting,Gravity Casting Handle,Aluminum Parts

Hoteng Machinery Co., Ltd. , http://www.nbdiecastings.com

Next Article
Prev Article